How to Change Electric Guitar Strings

If you don’t yet know how to change electric guitar strings, it’s about time you did because these need to be replaced more often than an acoustic or classical guitar string. The process might take some getting used to, but it is straightforward.

Materials You’ll Need

  • New electric guitar strings
  • Wire cutters
  • Guitar cleaning solution (optional)

Step 1: Remove the guitar strings

string-cutterYou can do this two ways, peg or by turning the machine. Either way, loosen the string so you can unwind and pull the string using your hand. You can tell the string is coming loose if the string has a deeper sound if you pluck it.

It is possible to just cut the strings, but the above technique is better as it lowers tension slowly.

  • If you’re new to restringing, remove the strings one by one.
  • After the string has come loose, unwind the string from the peg and get it off the electric guitar.

Step 2: Take the strings off the bridge

If you’ve got a Fender Stratocaster or any kind of string through guitar, draw the strings from the rear of the guitar. You can simplify the process by pushing the strings, making sure there is some slack so it is easier to hold. Hold the string along the metal end – it looks like a donut – and pull it out slowly.

  • If the bridge is of the wrap around type, you can draw it out from the bridge’s underside.
  • Yanking the strings out is a bad idea as it might damage the guitar.
  • Majority of guitar strings are straightforward. By following the string you’ll be able to remove the string out quickly.

Step 3: Clean the guitar

Now that you know how to change electric guitar strings Ibanez, it’s also a good time to clean the guitar. All you need is a lint free cloth to wipe the dirt and dust off the guitar.

Cleaning an electric guitar is easy and should not take long. If there is stubborn dirt on the hardware, buy a fret cleaner or guitar cleaning kit and you’ll be done in no time.

Step 4: Put the new strings in

Set the guitar on a soft, flat surface. Place a blanket or towel under the guitar to prevent scratching. You may position the guitar so the head is along the edge as it can make tuning easier.

Step 5: Adjust the tuning post hole

Turn the tuning post so the hole is facing you. The hole must not point towards the string so it’s parallel to a fret. If you are going to play the guitar the hole points upwards.

Step 6: Thread the strings

Get the first string in the bridge and in the tuning peg. Start threading from the guitar’s interior out. Most guitarists begin with the top E, the thickest string or the 6th string.

Slide the string the reverse manner of how you removed the strings. Now set the string in the tuning peg hole, drawing the string away off the guitar. provide around 3 inches of slack as you’ll be tightening that up when you tune it later.

The tuning pegs on electric guitars do not have marks, but it is best to replace the strings in the same manner you removed them. In the majority of electric guitars, the top string is for the first peg.

Step 7: Shape the string into an S shape

To do this, hold the string on either peg side and shape it into an S. If you want to know

how to change electric guitar strings Ibanez you must know how to do this.

Hold both sides, set your hands clockwise and crimp so the string resembles an S. Your left pushes up in the direction of the other tuning pegs while your right hand is directed towards body.

Step 8: Wrap the string end along the other half to secure the string

Hold the string’s end and pull it below the string’s other side. Once you get under the string, grab the other end and take it to the top and pull it tight. Pull along your guitar’s tip, giving you a string loop. If done right you’ll end up with a coiled string and the turning peg and string meet.

Step 9: Hold the string lightly as you tighten

the-guitarPosition your index finger 2 inches on the string before it connects with the tuning peg. Just hold, no need to pin. Slowly turn the tuner counterclockwise. Make certain the string winds along the peg evenly.

Use the tuner to reach the appropriate tension. If you’re not sure, tighten lightly to avoid breaking the string.

Step 10: Repeat the steps above for the other strings

Now that you have string in place, use the same procedure for the other strings. Make certain the fretboard is cleaned after each string is removed and there’s some slack prior to tightening.

If your guitar head comes with a 3×3 configuration, you have to reverse tune it. This means just follow the instructions above, replacing up with down and left with right.

Step 11: Cut the excess string

Use your wire cutters to cut the extra string. Don’t remove all the excess string so there is abut half an inch in case you want to tune it deeper.

Step 12: Tune your electric guitar

Once you’ve got the strings attached, tune your guitar the same way you always do. It’s a good idea to tune more often to stretch the strings so it gets accustomed to the tension. However you can resume normal tuning after a couple of days or by playing the guitar regularly.

 How to Change Electric Guitar Strings Video

Here is a guide showing how to string an electric guitar:

 Tips and Warnings

  • Change the electric guitar strings when they get gummy or dirty. If the strings go out of tune often, it’s a sign a change is needed. Anytime the strings feel sticky or out of sorts, get replacements.
  • Make sure you’ve got the right strings for your electric guitar. Majority of the time, you will need lite or regular weight strings.
  • You can change string configurations or use bigger gauges, but you can never use strings that are not meant for your electric guitar.
  • If there’s rust on the fret and other hardware, clean it first before putting on the new strings.
  • Do not use very heavy strings as it could snap the guitar’s neck over time.
  • For extra lite, lite and medium strings, you’ll want the high E to be 008-.0011 thick.
  • You will need heavier strings if you utilize drop tuning.
  • Don’t use abrasive products when cleaning your electric guitar. They will cause permanent damage and make things worse.
  • Buy only high quality strings. Cheap ones won’t last and they’ll snap with just the slightest pull.

Conclusion

Figuring out how to change electric guitar strings is no more complicated than removing those on an acoustic or classical guitar. By following the steps above you’ll have no issues when it comes to replacing and restringing any electric guitar.

We will be happy to hear your thoughts

      Leave a reply